Fanuc 21i-t parameter manual

Upload aoaby. Embed Size px x fanuc 21i-t parameter manual x x Warning notices are used in this publication to emphasize that hazardous voltages, currents,temperatures, or other conditions that could cause personal injury exist in this equipment ormay be associated with its use.

Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Caution Caution notices are used where equipment might be damaged if care is not taken. Note Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication.

Fanuc 21i-t parameter manual

Follow along with the video below to see how to install our site as a web app on your home screen. Note: This feature may not be available in some browsers. This website or its third-party tools process personal data e. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise. How to install the app on iOS. Log in Register. Search titles only. Search Advanced search…. Forums New posts Search forums. Media New media New comments Search media. Everywhere Threads This forum This thread. New posts.

In the above example, set 33 as the number of the pitch errorcompensation position for the reference position. When a reference position isalready set, reference position return is performed using rapid traverseand deceleration dogs are ignored.

.

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply.

Fanuc 21i-t parameter manual

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein.

Moonlight restaurant goa

The operation time is automatically preset to 0 during the poweron sequence and the cycle start from the reset state. This prevents the reference positionfrom being set again without dogs. If the block containing the sequence number set with this parameter is executed while the program set with parameter No. The rotation block of a normal direction control axis is not inserted whenthe rotation insertion angle calculated during normal direction controldoes not exceed this setting value. This soft key enables the entry of , , and using soft keys. OLS When an overload torque signal is received in a peck drilling cycle of asmall diameter, the feed and spindle speed are0 : Not changed. The numeral of a suffix indicates the bit position in a code. RWM RWD signal indicating that rewinding is in progress0 : Output only when the tape reader is being rewound by the reset and. CQD The method used for determining the amount of travel in circular interpolation is: 0 : Series 16 type. If a compensation value exceeds the value specifiedwith this parameter, a servo alarm No. MER When the last block of a program has been executed at single blockoperation in the MDI mode, the executed block is:. CMV When a move command and auxiliary function are specified from theCNC, and the system is awaiting the auxiliary function completion signalafter completion of the specified axis movement:. NOTEFor the T series, a decimal point and negative sign aresupported for commands for the second miscellaneousfunction, regardless of the setting made with this parameter. KEY2: Enables setting data and macro variables to be input.

.

If the block containing the sequence number set with this parameter isexecuted while the program set with parameter No. It rotatesin reverse direction degrees two rotations when G90 B0. After this parameter has been set, the power must be turned off then back on for the setting to become effective. Carousel Next. Ifa difference synchronization error which is greater than the valuespecified in this parameter is detected, a servo alarm No. Page When 0 is set, is assumed. However, the current position in the CNC includes a servo system delay, so that the position is shifted from the machine position by an amount corresponding to the servo system delay. That is, the fluctuation in the spindle speed is not detected until the specified time elapses from when the specified spindle speed is changed. Programt 1 Programt 1.