Rotex a1

S a f e t y I n s t ru c t i o n s rotex a1 n d S t a t e m e n t o f Wa rra n rotex a1 y When working on the heating system, make sure that the main switch granny blow.job in the off position at all times and secured against accidental switching on, rotex a1. Only authorised and properly trained specialists heating specialists may perform work on the heating system. The minimum distances to walls and other objects, rotex a1, stated in chapter 1, must be observed unconditionally. The correct installation of the temperature sensors and the safety temperature limiter must be checked before starting up the boiler for the first time.

Print on Demand. Reprinted in 0 with the help of original edition published long back. As these are old books, we processed each page manually and make them readable but in some cases some pages which are blur or missing or black spots. It is an eBook edition of the original edition published long back. We found this book important for the readers who want to know more about our old treasure so we brought back in ebook pdf format. These are scanned images of the original book in pdf format.

Rotex a1

.

The control system faults short-circuits and failures of the sensors and indicates rotex a1 faults. In order to do this, turn the operation mode selection switch pos. Do the electrical connections meet regulations?

.

Rotex has been setting and shattering standards for industrial separation equipment since Rotex Global patented the innovative concept of Gyratory Reciprocating Motion and perfected it over years of lab testing, custom installations and field experience. No other solution combines low-angle screening, long-stroke and low-frequency characteristics in a single machine. This dynamic combination results in greater efficiencies, superior particle accuracies and higher yields. A host of Fortune companies have trusted Rotex Global for decades. Ask your representative about our current and past partners. Every Rotex Global machine and part is backed by a team of service representatives and technical support staff who offer guidance before, during and after the sale.

Rotex a1

Hide thumbs. Table Of Contents. Table of Contents. Quick Links. For the operator.

Brush medibang

Displaying and Adjusting the Parameters There are three setting levels: 1. Average Temperature Shut-off in the case of a slow rise in temperature : The summer shut-off activates if the actual and average outdoor temperature reach the set value. The sound insulation cap sits on the burner panelling and is easy to remove fig. It is advisable to reset the counter after every maintenance check. This does not have a negative affect on the functioning of the unit. The combustion chamber can only be opened from the top. After the connection work has been completed, the A1 is ready for operation and may be put into operation by trained personnel. A flashing in the display indicates a short-circuit of the corresponding sensor and a flashing in the display indicates a failure of the corresponding sensor. As these are old books, we processed each page manually and make them readable but in some cases some pages which are blur or missing or black spots. In this area, the air-flue gas pipe is either led through a protective pipe with necessary fire resistance or separated from the timberwork pos. The boiler is connected with the LAS connection set, order no. The burner is adjusted at the factory for use with the type of gas supplied by your energy provider see adjustment sticker. The air supply may be installed with pipes made of synthetic material, 50 mm, or with flexible lines. The unit is automatically shut off and locked.

Table Of Contents.

When installing a gas heating system, you must observe the regulations described in TRGI G and the regulations of your gas supply firm. Do not fill the heating system until all installation work is finished. Only when all these questions can be answered with yes may the unit be put into operation. Used For: the processing of water when the heating operation is turned off. Indications for installing the tanks in the heating system may be found on fig. Adjustment: According to individual choice of temperature. Remark: The sensor lines should always be installed separately. With the burner running and the boiler warmed up, use the gas fitting screw pos. Procedure: Turn off the main switch of the boiler and unplug the storage tank sensor. The other is the US , a space saving tank made of high-grade steel which fits under the unit. If the water used for filling and replenishing the boiler has a particularly high degree of hardness, measures should be taken to stabilise or soften the water. The flow temperature is regulated according to the outdoor temperature. To connect the heating circuit and hot water storage tank e. These instructions should be read carefully before you begin installation. Important: The water pressure should be checked with the manometer 1.