Snake knot paracord

A single color knot, snake knot paracord, this technique creates a slim, tight pattern that is ideal for places where a thinner cord is desired such and zipper pulls or lanyards. The snake knot is also suitable for all thicknesses of cord and is a versatile, easy technique to master.

This instructable will show how to make a wrist lanyard using paracord and the snake knot. The lanyard can be used to secure a key chain, knife, multi-tool, flashlight, cell phone, camera, binoculars, compass, etc. More projects, links, knot references can be seen on my blog page, Stormdrane's Blog. You'll need about 4. The paracord I used is from the Supply Captain.

Snake knot paracord

.

You may also like May 15, You may remove a small amount of the paracord's inner strands by pulling them out, trimming snake knot paracord scissors, and pulling the paracord outer sheath back over the strands, leaving room to insert the other color.

.

This would be a great craft project for a summer camp or nature club. Or make them on a rainy day! The completed snakes are fun to play with. This is an easy project for beginners. Adult help will be needed to fuse the paracord since it involves a lighter. The snakes are flexible, so you can pose them to look like they are slithering. I love all the different colors of paracord!

Snake knot paracord

But instead of carrying around a small hank of paracord in your back pocket, you can wear it in the form of a stylish and handy bracelet. The following method is one of my favorites, combining the intriguing, easy and compact snake knot with a hardware-free adjustable closure as made Internet Famous by the most recent Mad Max movie. If significantly smaller, use less. Other than that, you just need scissors or a sharp knife, a lighter, and a nail, marlinspike, or paracord tool to help you complete one of the steps. Step 1: Start by finding the midpoint of your cord. Hold the midpoint and your non-dominant hand and have the working ends pointing towards you. Step 2: take the left side of your cord and loop it around to the right, going over top…. Step 4: now, take the end of the right side of the cord and pass it under and behind the left side….

Aabbcc skin color

Visit my blog page for more knot related projects, links, and resources: Stormdrane's Blog. Before you go. Take the center of the length of cord and bring it thru the attachment, I'm using a swivel clip. The snake knot is also suitable for all thicknesses of cord and is a versatile, easy technique to master. Previous Post Next Post. The paracord I used is from the Supply Captain. Continue this procedure until you've done about 10 snake knots you can count them down either side. Pull to tighten. Difficultly level: Easy Time required: 15 minutes. It will be hidden under the first knot. Cross the left hand leg over the right to form a loop. You'll always have those at the start and finish of the snake knots, I prefer to have them end up on the same side of the lanyard so one side appears to have a more uniform look, but it's not required. Again flipping the work over, you'll see two parallel cords of the same color which will be split with the cord on the right going under, around, and pulled thru with the hemostats, then tightened up. More projects, links, knot references can be seen on my blog page, Stormdrane's Blog.

This instructable will show how to make a wrist lanyard using paracord and the snake knot.

Use the scissors to trim off the excess cord and quickly melt the ends with a lighter so they don't fray. It will be hidden under the first knot. More projects, links, knot references can be seen on my blog page, Stormdrane's Blog. The connection of the two colors will be just on the other side at this point. Paracord Techniques: How to do a Snake Knot. Before you go. The snake knot is also suitable for all thicknesses of cord and is a versatile, easy technique to master. The paracord I used is from the Supply Captain. Previous Post Next Post. You may also like May 15,