Ipod nano 1 battery

I recently found an old iPod Nano 1st Generation that was sitting in a drawer, collecting dust since around or When it was in use, it was slightly damaged with a small dent on one side of the back. I also noticed the back was slightly coming off on the opposite side of the dent, but I assumed it was just because of ipod nano 1 battery dent.

The rear panel is secured to the front case by eleven clips permanently attached to the rear panel. These clips lock onto small tabs machined into the front case. To free the tabs, they must be pushed down and away from the iPod's case. Note the location of all tabs on the rear panel. When using an iPod opening tool to free the rear panel, be sure to work the tool at the location of these clips. Opening the iPod can be challenging.

Ipod nano 1 battery

Enter your email address below, and we will notify you when this product is back in stock. This iPod nano 1st Gen replacement battery is what you need to bring your dead iPod back to life! Battery degradation is an inevitable part of your iPod's lifespan — extend it with this new replacement battery compatible with the first generation iPod nano. Then use your device until it shuts off due to low battery. This replacement battery may be a slightly more snug fit than the original due to a small variation. Learn more about safe lithium-ion battery handling and proper disposal. This product can expose you to chemicals including lead which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www. All our products meet rigorous quality standards and are backed by industry-leading guarantees. Condition: New. Shipping restrictions apply. Batteries may only be shipped within the contiguous USA at this time and may only ship via standard shipping. This item is currently Out of Stock. Notify me when it is back in stock!

What you need. I am not very experienced with soldering, so I practiced on a little blinking christmas tree kit before attempting this, and I think that was useful.

.

On September 7th, , Apple announced the iPod Nano with Steve Jobs pointing to the small watch pocket in his jeans and asking, "Ever wonder what this pocket is for? The iPod Nano was the successor to the iPod Mini. This was a very risky move for Apple as the iPod Mini was selling extremely well. This risky move turned out to be the correct decision and Apple went on to sell millions of the iPod Nano-lineup. On the 11th November , Apple issued recall program for all first generation Nanos, since there were incidents involving iPod Nano 1st gens that caught on fire.

Ipod nano 1 battery

This instructable goes over how to change the battery in your 1st Gen Ipod Nano. This ipod was found in the junk pile at instructables with a bloated battery. Next time your friend throws out their old ipod, try to fix it up! You need a bit of supplies to complete this: A Broken iPod New Battery Soldering Iron a note on batteries, you can get them off of ebay, but i got mine from iFixit. First you need to make room for the new battery, do this by desoldering the old one from the logic board. Next carefully solder the new battery onto the board, the order from the left side of the back of the ipod is: White Red Black. Lastly close the ipod back up by snapping it together and charge it! Easy right? Well not exactly, it seems that this ipod had a bit more problems than a broken battery, after charging and trying to get it to work in diagnositc mode i got the second image: a total hard drive space of

Dnd 5e srd

To open the solder holes, open a safety pin and push it against the solder blocking the hole. This notch prevents the board from sliding out in the next step. Lifetime Guarantee. Learn more Sign up. Get started with your Apple ID. In order to avoid damage, lift the solder tip off the connection as soon as the solder melts and the lead slides out. View in context. Replacement Guides. Insert the large iPod opening tool into the seam between the front case and rear panel of the iPod, below the dock connector. To keep the leads in place, it may be helpful to first bend the battery leads into their final shape, then insert the stripped ends into the holes. Solder the connection by momentarily placing the tip of the soldering iron against the connection, melting solder into the connection, and quickly removing both the solder and the tip of the soldering iron from the connection.

Enter your email address below, and we will notify you when this product is back in stock. This iPod nano 1st Gen replacement battery is what you need to bring your dead iPod back to life!

Flip the logic board and battery over so the bare ends of the battery leads are facing up. Question marked as Best reply User profile for user: the fiend the fiend. A forum where Apple customers help each other with their products. Get started with your Apple ID. Gently lift up on the dock connector end of the logic board to ensure the logic board is free. If they can, pass it to them. User level: Level 7. Do not simply put it in your household trash. Add a comment. Thank you in advance. This product can expose you to chemicals including lead which is known to the State of California to cause cancer and birth defects or other reproductive harm.