Playstation 2 laser replacement

Disconnect all cables from the console and flip the unit over to reveal its base. Locate the 6 feet on the base of the unit. Pry them off using a spudger to reveal the screws. Note: One of the feet is located under the sticker shown in the photo.

Replace the laser assembly in your optical disc drive. Replacing the laser requires you to have or purchase a new laser. Flip the PlayStation 2 over so it lays with the bottom of the device facing upwards. Some models have a different number of screws and feet. Remove all the feet and screws in the bottom of the case. The 10 screw model has 6 screws in the bottom-most portion and 4 in the upper tray.

Playstation 2 laser replacement

Use this guide to help identify which optical laser lens replacement will fit your PlayStation 2 console. Note: Replacing the laser lens will normally require a soldering iron to remove an anti static point solder blog before install. Laser lens models can normally be identified from the console model but it is always advisable to physically remove and check the old laser prior to ordering any replacement to ensure that it is the model you expected, and that the new part is the same model or listed as a compatible replacement for the model of laser you have. Lasers will need to be fitted to the deck unit inside the console, this requires some additional rebuilding, unscrewing runners to remove the old laser and put the new one in place. This is only a few additional steps but if you are less confident with completing the repair, or you believe other parts of the laser mechanism is not working properly, you can opt to purchase the deck with the laser pre-installed. Remember the anti static solder blob will still need to be removed prior to installation or the laser will not operate, this applies to all laser units, whether attached to the deck or not. This site uses cookies to provide you with a great user experience, by using ZedLabz. Discover the latest stuff from our wide range of partners, including exclusives only available at ZedLabz. Gaming display stands See More "Close Cart". Merchandise See More "Close Cart".

Remember the anti static solder blob will still need to be removed prior to installation or the laser will not operate, this applies to all laser units, whether attached to the deck or not. To facilitate the removal, playstation 2 laser replacement, it is recommended to pry open the half closer to the power switch first while rocking the top cover towards the front of the bottom case. Carefully remove the power cord that attaches the top and bottom halves by disconnecting the power cord assembly from the top case.

.

Disconnect all cables from the console and flip the unit over to reveal its base. Locate the 6 feet on the base of the unit. Pry them off using a spudger to reveal the screws. Note: One of the feet is located under the sticker shown in the photo. Removing this sticker will void any warranty with Sony. Remove all six 4. Starting at the corner at which the power and Ethernet ports are located, pry open the outer shell using a spudger and continue around the entire unit. Note: You may use your hands for additional force to separate the two pieces of the outer shell.

Playstation 2 laser replacement

The screws on the right are a bit deeper inside the shell as like the rest but are the same size. Separate the clips at the front and the overhanging side from their mounting using a Prying Tool. With a plastic tool, lightly press down these two levers at the same time. Ideally, the CD should now start to spin. If it doesn't spin, the whole drive or other parts of it may be damaged and need to be replaced. Now, there are 3 flat cables to disconnect. Caution: Some have a small clamp that must first be released, so that you can carefully pull them out. Cable 2 on the other hand, has a clamp. This must be carefully preyed up from both sides before you can disconnect the cable. Caution: It's still held on the underside by a flat cable!

Holasun

Carlos Bragatto - Feb 16, Parker Ludwig - Jul 7, Reply. Discover the latest stuff from our wide range of partners, including exclusives only available at ZedLabz. What you need. Remove the four 6. Laser lens models can normally be identified from the console model but it is always advisable to physically remove and check the old laser prior to ordering any replacement to ensure that it is the model you expected, and that the new part is the same model or listed as a compatible replacement for the model of laser you have. Alexander Wiand - Nov 8, Reply. Add Comment. Be carefull, as it still attached to the laser, just guide it slowly towards yourself. You are appreciated. Some lasers come without the anti-static security. Removing this sticker will void any warranty with Sony. Gaming display stands See More "Close Cart". Looking for a reliable seller.

Replace the laser assembly in your optical disc drive.

Cancel: I did not complete this guide. You're Finished! Brands See More "Close Cart". Peel the warranty sticker located next to the main power switch straight away from the case. Be carefull not to break it, it can break easily. Mohsen - Jan 21, Reply. Small - px Medium - px Large - px. Open the ZIF connector. Gaming display stands See More "Close Cart". To reassemble your device, follow these instructions in reverse order.